vSAN ReadyNode are x86 servers, available from all the leading server vendors, that have been pre-configured, tested and certified for VMware Hyper-Converged Infrastructure Software. Each ReadyNodes is optimally configured for vSAN with the required amount of CPU, memory, network, I/O controllers and storage (SSDs, HDDs or flash devices).
VMware vSAN Hybrid TCO and Sizing Calculator Virtual SAN or vSAN is a software-defined storage (Hyper Converged) for VMware vSphere environments. Main goal of sing vSAN in VMware vSphere environments, is reducing implementing cost. So calculating TCO and device sizing will help to achieve better results. As vSAN technology owner, VMware has provided an online tool for calculating TCO and sizing for vSAN. The online tool is very useful for IT administrator to find cost of vSAN implementation with different scenarios. The online tool has four different sections: Sizing Inputs: You should fill the sizing inputs form with some information about your environment. Sizing Results: The online tool will calculate results according to the sizing inputs and show the result on this section. TCO Input: You should enter required information for Total Cost of Ownership. TCO Results: According to the information, the tool will calculate and shows the result for TCO calculation. Sizing Inputs This section is using for enter virtualization environment specifications. You must specify the some important information for the online tool to calculating vSAN TCO and sizing. The online tool can calculate requirements according to virtualization platform, there is two platforms for calculations: Server Virtualization Desktop Virtualization The online...
EMC Unity Drive and OE Compatibility Matrix EMC Unity storage systems supporting the below disk drives: Unity SAS Flash 2 Drives – For use in FAST Cache, FAST VP or all-Flash-pools Unity SAS Flash 3 Drives – For use in all-Flash-pools only Unity SAS Flash 4 Drives – For use in all-Flash-pools only Unity Spinning Drives To function properly drives installed in an EMC Unity storage system require that the array be running the minimum required revision of the Operating Environment (OE). EMC provides a document which lists the drive part numbers supported for Unity storage systems and the minimum software revisions required for each drive model. Notes: The drive part number (PN) appears on a label on the front of the drive carrier. Note that although the OE GUI may display an alpha suffix at the end of the PN (like EFD) these characters are not part of the actual orderable PN. All drives listed in this document are RoHS compliant. Unity drive models use the following prefixes: D3 = AC storage D3FC = AC FAST cache D3AF = AC storage when used in All-Flash-Array (AFA) D3N = DC NEBS storage D3NFC = DC NEBS FAST Cache The following...
EMC VNX2 Drive and OE Compatibility Matrix The document will help you to know that the minimum compatibility between VNX storage system OE and disk drives. The supported part numbers and minimum version of software are listed. Before installing a new disk in a storage system, use the EMC Unisphere Manager to determine the VNX OE revision running on the storage system. In Unisphere Manager, the VNX OE revision appears on the Software tab of the Storage System Properties dialog box for the storage system. Note 1: Changes and additions in the tables since the last revision of this document are noted in red type. Note 2: The disk part number (PN) appears on a label on the front of the disk carrier. Note that although the OE GUI may display an alpha suffix at the end of the PN (like PWR or SSD) these characters are not part of the actual orderable PN. Note 3: PNs in tables with a ‘YES’ entry in the Spin-Down Support column may report a suffix of PWR through the OE GUI (EX: 005049278PWR). This PWR suffix is used by the OE and is not part of the actual orderable PN. Supported Disk Drives...
There is a standard way to configure iLO for HPE ProLiant servers, HPE iLO can be configured after boot-up via SETUP utility on all type of servers and generations. If you press [F8] during boot-up, iLO configuration utility will be appeared and then you can configure all iLO configuration such as network connection.
